The elevation function is not working properly. Resolution: • Unplug the treadmill from the outlet. Wait approximately 60 seconds, allowing the lower board to discharge built-up energy. • Remove the motor cover. • Verify that there are no lights lit on the lower circuit board (this indicates built-up energy has discharged and it is safe to check it). • Verify that all wires are securely and correctly placed on the lower circuit board, especially the large wire harness on the top of the circuit board with 12 different colored wires coming out of it.

SPORTSMITH, Fitness Equipment Parts & Products Superstore! We are dedicated to helping you maintain your fitness equipment as cost effectively as possible. We offer 1000's of quality parts for cardio and strength equipment. Find Exercise Bike in Exercise Equipment Exercise equipment is available for sale in Dartmouth – dumbbells, weights, bench, Bowflex, elliptical, treadmill, and more on Kijiji, Canada's #1 Local Classifieds.

• Double check that all connections are secure, especially the console cable. Unplug and reconnect the console cable at the top of the console mast – see the assembly instructions in the owner's manual for this step. Can’t acquire/read heart rate. Resolution: • Good contact with the grip is essential.

Rosemount Rosemount™ Engineering Assistant 6 Software In three easy steps, the Rosemount Engineering Assistant 6 Software sets up the Rosemount 3051S MultiVariable™ Transmitter with HART® protocol for mass flow installations. This is a PC-based software package engineered for Microsoft® Windows™ operating systems (Windows 7, 8, 10). Rosemount engineering assistant software. The Rosemount Engineering Assistant 5 Software is a PC-based software package for Microsoft® Windows™ operating systems. This software works as the communication interface to Rosemount mass flow transmitters, such as Rosemount 3095 and 3051S MultiVariable™ Transmitters.

Before taking pulse, stop walking and step on side rails and place hands on contacts. • Try gripping the handlebar contacts over the top, with your thumb next to your index finger instead of gripping it with your thumb under the handlebars. • Verify that there are no lights lit on the lower circuit board (this indicates built-up energy has discharged and it is safe to check it). • Contact heart rate grips are not intended for continuous reading.

All pages on this site are copyrighted. Chart fx internet 6.2. *Microsoft, MS, ActiveX, VB, Visual Basic, Visual C++, Windows, the Microsoft Internet Explorer Logo, and the Microsoft Windows logo are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

Rather, try holding the grips for 10-20 seconds at a time for an accurate reading. • Static electricity can damage the heart rate grip receiver and/or grips and cause either an “HR” or no reading at all. • Refer to the product manual that came with your machine for more information on the heart rate function. Static electricity Resolution: Eliminate static • Stay away from nylon clothing. Wear cotton clothing to reduce static on the body.

• Use an anti-static spray on clothing and/or around treadmill. • Try a different pair of shoes. Some shoes seem to add to static shocks. • Use humidifier to increase humidity in the air. Resolution: Improper grounding • Verify that the power cord is plugged into a 3 prong outlet without using a two pronged adapter Resolution: Rubber mat • Place a under the treadmill to reduce the static carried from the carpet. Resolution: Lubricate deck Resolution: • A worn belt and deck can contribute to premature motor and motor control board failure.

My running belt does not move. Resolution: Check cables or loose wires.

• Double check that all connections are secure, especially the console cable. Unplug and reconnect the console cable at the top of the console mast – see the assembly instructions in the owner's manual for this step. • Make sure the console cable is not pinched or damaged in any way. • Turn the power off, unplug the power cable and wait 60 seconds. Remove the motor cover.

Wait until all red LED lights have gone off on the motor control board before proceeding. Next, verify that none of the wires connected to the lower board are loose or disconnected.